Pleasant View Electronics

Electronic Parts Supplier - Electronic Component Parts & Supplies

Breakout Boards

Breakout BoardBreakout Boards

Breakout boards make things easier to interface immediately, especially with SMD type IC’s and other small components. Breakout boards also usually have any necessary supporting componentry needed to make the device operate immediately.

This is the newest revision and fixes issues with the last board. This breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART IC to convert a USB stream to ....More
SparkFun USB to RS-485 Converter
This is a breakout board for the SC16IS750, a handy chip used to convert I2C or SPI serial signals to a single-channel, high-performance UART. As an application example: we use thi....More
SparkFun I2C/SPI-to-UART Breakout - SC16IS750
Opto Isolated 5VCC input, Dual Relay module for any project.
TTL Compatible with Arduino or other micro controllers.

LED indicatorsfor input activity.

Power: ....More
Relay - Dual SPDT 5V Coil
The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and st....More
L298N - Full-Bridge Dual Motor Driver w/ Breakout Board
Compact PC board Pulse generator utilizing the 555 IC.
5-15VDC input power
15mA output drive @ 5VDC; 35mA @ 12V Power
4 jumper selectable frequency ranges....More
Pulse Generator Board
This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin ....More
CD74HC4067 - Analog/Digital MUX Breakout
General use module generates pulses from approximately 4Hz to 1.3Khz. Utilizes the popular NE555 timer IC operating as an astable multivibrator. Module has ten-turn frequency adjus....More
NE555 Frequency Adjustable Pulse Generator
This is a simple breakout board for the popular XBee product from Digi. This board breaks out all 20 pins of the XBee to a 0.1" standard spacing dual row header. The spacing betwee....More
Xbee Raw Breakout Kit
Single Relay module for any project.
- Transistor controlled logic, compatible with any 3v or 5v micro controller.
-LED indicates Relay activated.
-Active High Logic to....More
Relay Board - 5V SPDT
Compact, Non-isolated, adjustable linear voltage regulator module.
-LM317 IC for a wide range input/output voltages.
-Built in heat sink and filter capacitors.
Ten turn....More
DC Voltage Regulator Module - Adjustable Output
This is a breakout for the SOIC version of the 74HC595 shift register IC. Clock in data and latch it to free up IO pins on your micro. All pins from the IC are broken out to standa....More
SparkFun Shift Register Breakout - 74HC595
Sparkfun - Level Converter - Bi-Directional

If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional ....More
Logic Level Converter - Bi-Directional
Infrared LEDs emit non-visible light. Along with an IR receiver they can be used for remote control and even basic remote data communication. The only problem is that your Arduino....More
SparkFun Max Power IR LED Kit
The Inline Power Driver is a MOSFET Controlled TTL Level board, a breakout boardfor for the RFP30N06LE N-Channel MOSFET. If you are looking for a little more control over Driving ....More
Inline Power Driver Board

Hits: 1034

Updated: January 16, 2017 — 11:57 am
Pleasant View Electronics | © 2017 Frontier Theme